Skip to content
MachineCalcs

Surface Feet per Minute (SFM) Calculator

Convert cutting speed (SFM or m/min) and tool or work diameter to spindle RPM, with recommended cutting speeds by material. For turning, milling and drilling. Metric and imperial.

Inputs

mm
m/min

Results

Spindle speed(n)
382rpm

  • RPM = cutting speed ÷ (π × diameter). In imperial: RPM = (SFM × 12) ÷ (π × diameter in inches) ≈ 3.82 × SFM / D.
  • For milling and drilling the diameter is the tool diameter; for turning it is the work diameter.
  • Cutting speeds in the table are starting points — tune for depth of cut, feed, coating and rigidity.

How it works

Spindle speed comes from the cutting speed and the diameter: RPM = cutting speed ÷ (π × diameter) In imperial that works out to RPM = 12 × SFM ÷ (π × D) ≈ 3.82 × SFM / D with D in inches; in metric, RPM = 1000 × Vc ÷ (π × D) with Vc in m/min and D in mm. Use the tool diameter for milling and drilling, and the work diameter for turning. The cutting speed itself depends on the material and tool — start from the table below and adjust.

Worked example

A 1-inch end mill running 100 SFM in mild steel: RPM = 12 × 100 ÷ (π × 1) ≈ 382 RPM. The same in metric — a 25.4 mm tool at 30.5 m/min — gives the same 382 RPM. The calculator returns this on load.

Reference data

Starting cutting speeds for single-point turning, in surface feet per minute, for HSS and uncoated carbide. Real speeds depend on depth of cut, feed, coating, coolant and rigidity — treat these as a baseline.

Typical turning cutting speeds (SFM).
Material HSS (SFM) Carbide (SFM) Notes
Aluminum 300 800 Free-machining; high speeds, watch built-up edge.
Brass 200 600 Free-cutting brass; very machinable.
Bronze 120 350 Harder than brass.
Cast iron (gray) 60 200 Abrasive; carbide preferred.
Mild steel (1018) 90 350 General low-carbon steel.
Alloy steel (4140) 60 250 Heat-treatable; lower when hardened.
Stainless (304) 50 200 Work-hardens; keep feed up, avoid dwelling.
Tool steel 45 175 Hard; reduce speed as hardness rises.
Titanium 35 150 Low speed; heat builds fast.
Plastic 400 800 Sharp tools; clear chips.

Source: Standard machining references (Machinery's Handbook turning-speed tables; common shop practice). Verify against your tooling maker's data.

Frequently asked questions

How do you convert SFM to RPM?
RPM = (SFM × 12) ÷ (π × diameter in inches), which is about 3.82 × SFM ÷ D. In metric, RPM = (1000 × Vc) ÷ (π × diameter in mm), with Vc in m/min.
What is surface feet per minute (SFM)?
SFM is the cutting speed — how fast the cutting edge moves across the workpiece surface, in feet per minute. The metric equivalent is surface metres per minute (m/min).
What SFM should I use for aluminum, steel or stainless?
Use the cutting-speed table below as a starting point: roughly 800 SFM for aluminum, 350 for mild steel and 200 for stainless with carbide; about a third of that with HSS. Then tune for your setup.
Is the diameter the tool or the workpiece?
For milling and drilling, use the tool diameter. For turning, use the workpiece diameter at the cut.
How much faster is carbide than HSS?
Carbide typically runs two to four times the cutting speed of high-speed steel for the same material, because it keeps its hardness at much higher temperatures.
Does it work in metric (m/min)?
Yes — toggle SI/Imperial to switch the cutting speed between SFM and m/min and the diameter between inches and mm.

Method & assumptions

  • Cutting speeds are general turning starting points; milling and drilling, coatings and high-feed strategies shift them.
  • This finds spindle speed from cutting speed — to go the other way, RPM × π × D gives the surface speed.

Related calculators